As the old saying goes, an ounce of prevention is worth a pound of cure. This definitely applies to the flooring in your facility, where dust and grit can act as an abrasive on hard and soft surfaces alike. Regular cleaning and maintenance can extend the life and look of your floors, so you can avoid spending your repair budget on unnecessary flooring replacement costs. Use these tips to help you save resources by preserving your VCT, ceramic, terrazzo, concrete, carpet floors and matting.
VCT (Vinyl Composition Tile)
Remove finish (if any).
Dust mop and clean with an 4:1 emulsifier solution.
Apply to floor and allow to dwell for 15 minutes.
Agitate with floor machine and black pad, remove with wet vac.
Check floor thoroughly for any missed spots.
Helpful tip: For new floor, check with the installer for appropriate cure times before applying excess cleaning solutions or floor strippers.
Keep free of debris and dust using a dust mop.
Cleanse concrete with a low suds cleaner and an automatic scrubber, the most productive and economical choice for cleaning concrete floors.
Helpful tip: Automatic scrubbers are sized to the total area of the facility and the width of any areas needed to be cleaned. Larger units may be used for open areas and rider scrubbers increase productivity.
Dust mop or broom sweep. Use a good mating program to keep most dirt localized at the door and prevent it from grinding down the coating. Dust/mop up dirt that does get inside.
Wet mop with all-purpose cleaner.
Pro tip: The type of mop you use can make a significant difference in the overall cleanliness of your facility.
Reseal floors with a water-based sealer.
Annually or Biannually:
Undergo a gloss restoration. Floor surface must be clean, dry and have all previous finish materials removed.
Dust mop floor with a dust mop system to remove all debris.
Strip all finish from the floor with a rinse-free stripper.
Prepare the clean floor surface with the recommended floor pad.
Apply a stone floor coating per label directions.
Ceramic Tile & Grout
Clean with a traditional wet mop system, deck brush or automatic scrubber that utilizes cylindrical brushes. Avoid acidic cleaners.
Pro tip: The size and material of your wet mop should be taken into consideration when developing your cleaning system.
Deep scrub grout with all-purpose cleaner.
Reseal grout and apply according to label directions to a clean floor. Applying a grout impregnator will repel moisture and protect grout from soil, grease and oil.
Helpful tip: Seal tile upon installation before any other maintenance. This should be the only time you have to do this if the floor is maintained properly.
Daily to Weekly:
Depending on traffic, vacuum with fresh filter bag for maximum airflow and effectiveness.
Remove residue (if any) with an extraction cleaner. Increase dilution ratios to compensate for the soil loading.
The encapsulating chemical is brushed in, distributing it throughout the carpet pile, and allowed to dry. As it dries it crystallizes around the sticky, oily soils adhered to the carpet fibers causing them to release from the fiber.
In 20 minutes when they are dry (or at the next scheduled vacuuming) they can be vacuumed out.
After encapsulation utilize several carpet fans to dry the area before re-opening to foot traffic.
Helpful tip: High soil load areas need to be vacuumed with upright vacuums with brush bar agitation.
Vacuum to remove any dirt and debris trapped by matting.
Seasonally (winter/early spring):
If you can see that telltale whitish haze after vacuuming, this means that matting is full of ice melt residues that need to be removed.
Dilute an all-purpose cleaner at 1-2 ounces per gallon.
Work it into the surface with the brush.
Use an extractor with an encapsulating chemical to flood the matting. Wait about 10-15 minutes of dwell time, and then extract the solution.
Check the water in the recovery tank. If it’s still dark and dirty, repeat until the extracted water is clear.
Helpful tip: When extracting, allow the cleaning solution to flood the matting by using your extractor without the vacuum engaged. This gives ample time to dissolve the salt residues and to break up and suspend oily soils.
Be on the lookout for buildup from soaps and cleaners that can make the floor slippery. Rinse the problem areas with water as needed.
Consider using floor mats for high traffic areas on all flooring types. They will be your first line of defense against soils and substances tracked inside of your building.
As always, pay special attention to high-traffic areas like entrances, lobbies and busy hallways.